External vs. Submersible Pumps. Which one should you Use?
(Submersible Pumps)
(External Pumps)
For many people, it's never been a question of whether
to use a submersible pump vs. an external pump because most people
have smaller ponds and are used to just using a submersible pump.
They're easy to install, and are pretty reliable - so why even
consider an external pump?
There are a couple of reasons...
But before we go into that, let's briefly talk about the benefits of
submersible pumps first. For obvious reasons, a submersible pump is
named as such because it is designed to be placed in the pond, and
submerged under the water.
These are the easiest of all pumps to install, just drop them in the
water and plug them in - and you’re ready to do. Of course, you might
have some quick plumbing to do, attaching a hose to the waterfall or
to a submersible filter (another article entirely), but other than
that - that's pretty much all there is to it.
Submersible pumps range in size or gallons per hour, from 50 GPH all
the way up to 50,000 gallons per hour, but for most ponds - pumps
anywhere from 350 GPH to 4000 GPH will do just fine...
So why might you also consider an external pump instead?
Here are a couple reasons. First, external pumps can much more energy
efficient. Now, a typical swimming pool or spa pump won't usually fall
into this category - so be careful not to compare apples to oranges!
Pool pumps can also be huge energy hogs, so always check the amps to
compare different pumps together. Anything over 10 amps will draw a
significant amount of $$ out of your pocket every month in electrical
costs.
The external pumps that we are talking about are designed specifically
for ponds and water gardens, and are engineered for energy efficiency.
I'm not sure why those folks in the swimming pool and spa industry
haven't figured out how to this yet, but I'm sure they'll catch on
sooner or later.
I'm inclined to think the average pond owner is a bit more intelligent
than the average pool owner. Why else would someone choose a pool over
a pond? Unless of course you have both, but at any rate - let's just
assume that we're talking about external pond pumps here.
For comparison, a typical 4000 GPH (gallons per hour) submersible pond
pump will typically draw anywhere from 10 amps all the way up to 15
amps, depending on the brand. This can really burn a hole in your
wallet (or pocketbook) on a monthly basis, and in some parts of the
country will run you $50 - $70 in energy costs.
In contrast, a comparatively rated external pond pump like the William
Lim Wave I External Pump:
W.Lim Wave I -
Click Here for More Info
is rated at 4380 GPH at 3.47 feet of head, and only draws 2.3 amps -
that's 3/4 less energy consumption than the submersible pumps.
When you start getting into larger ponds, 1000 gallons up to 20,000
and above - it's usually a good idea to look into these more energy
efficient pumps.
For example, the 3/4 HP Dragon pump:
W.Lim Dragon Pump -
Click Here for More Info
will move 7,770 GPH at almost 5 feet of head (and under pressure) and
only burn 6.2 amps! That's impressive.
External pumps are almost always better for using with pressurized
external filters as well, as submersible pumps are not designed to
handle all the back pressure. Other benefits of using an external pump
include:
-> Easy to clean without getting your hands messy
-> Come with a removable leaf trap which clog less often
-> Easy to hook up to bottom drains or surface skimmers
-> Generally last longer, and easier to repair / replace parts
So that's it, more than enough information for you to make an educated
choice.
Just to recap:
For smaller ponds, and for simple installation and daily use,
submersible pumps are probably your best option. For larger ponds,
1000 gallons and above, it may be worth looking into an external pump
for your needs. Although they cost a little more on the front
end, the energy savings alone can often more than offset this increase
in cost during the first year of use alone.
|
